A shield anchor is a two-part masonry fixing made up of a segmented metal shield and a tapered bolt. As you tighten the bolt, the cone at its end pulls into the shield and forces it to expand, gripping the sides of the hole in brick, block or concrete. It's one of the most dependable medium-duty fixings for masonry — and one of the most misunderstood. This guide explains how it works, where it beats a sleeve or drop-in anchor, and how to install one without splitting the wall.

What is a shield anchor?

A shield anchor (sometimes called a Rawlbolt-style masonry anchor) has two parts: a metal shield made of three or four segments, and a bolt with a cone-shaped tip. The shield goes into a pre-drilled hole first. When the bolt is threaded in and tightened, the cone wedges inside the shield and pushes its segments outward against the walls of the hole. The grip comes from expansion — the harder you torque it, the harder it clamps the masonry.

The version we stock is the loose bolt (projecting) type: the bolt is separate from the shield, so the thread projects out of the wall once installed. That makes them ideal when the fixture slides over the stud — brackets, gate hinges, timber frames — and you then secure it with a nut and washer.

How do you install a shield anchor?

  1. Drill the hole to the diameter and depth specified for the anchor size, using a masonry bit. Depth matters: the shield must sit fully below the surface with the bolt able to project the right amount.
  2. Clean the hole. Blow or brush out the dust — debris at the bottom of the hole stops the shield seating fully and costs you grip.
  3. Insert the shield and tap it flush with a hammer, segments facing out.
  4. Offer up the fixture over the projecting bolt, or hang the bolt through the fixture before inserting it into the shield.
  5. Tighten with a spanner until firm. The cone expands the shield as it pulls in. Stop at firm — over-torquing is the most common mistake (see below).

When should you use a shield anchor?

Shield anchors earn their place in softer and more brittle masonry: brick, lightweight aerated block, and older stone. Because the shield is a large, multi-part sleeve, it spreads the expansion force over a wider area of the hole than a small expansion clip can. In weak block or facing brick, that means less chance of the substrate crumbling or cracking under load.

Typical jobs: fixing gate hinges and posts to brickwork, wall brackets, pipework and conduit clips, signage, shelving standards, satellite dishes and TV brackets, and battens or frames to block walls. If you're anchoring into solid structural concrete and need maximum holding, a heavy-duty concrete anchor or resin system is the better tool.

Shield anchor vs sleeve anchor vs drop-in anchor

 Shield anchorSleeve anchorDrop-in anchor
Best substrateBrick, block, stone — softer masonryBrick and concrete, general purposeSolid concrete only
How it gripsFull-length shield expands over the whole embedmentSleeve expands at one point along the bodyInternal plug expands the base
Fixture typeFixtures drop over the projecting studFixture sits under the nut/headThreaded rod or bolt screws in from above
Removable?Yes — unscrew the boltYes, with effortNo — permanently set
Watch out forNeeds correct hole depth for the shieldCan spin in oversize or weak holesNeeds a solid, deep concrete base

Rule of thumb: the softer the wall, the more the shield anchor's full-length expansion earns its keep. In solid concrete, the other two usually do the job for less.

What sizes do shield anchors come in?

Common trade sizes run from M6 up to M16, with shield lengths matched to the embedment each size needs. As a rough guide, bigger diameter means deeper embedment and higher load capacity — but always size the anchor for the substrate as much as the load. An M10 in soft aerated block can fail long before an M8 in dense concrete would. Check the load figures for your specific wall type before committing, and when in doubt, step up a size or switch to a heavy-duty anchor.

Installation mistakes to avoid

  • Over-torquing. Snapping the head or splitting the brick is almost always over-tightening. Firm is enough — the expansion is doing the work, not brute force.
  • Drilling oversized holes. A wallowing hole means the shield can't grip. Let the drill do the work, don't wobble it.
  • Fixing too close to an edge or opening. Expansion forces can spall the masonry face. Keep sensible edge distance — around 100mm minimum for mid-size anchors.
  • Reusing a failed hole. If an anchor has spun or pulled out, the substrate is damaged. Move to fresh material, or switch to a resin anchor to fill and re-bond the failed hole.

FAQ

What is a shield anchor used for?

Fixing fixtures to masonry — brick, block and stone — where a medium-duty, removable anchor is needed: brackets, gates, frames, pipework and signage.

Are shield anchors any good in brick?

Yes — brick is their sweet spot. The multi-segment shield spreads expansion pressure over a wider area than a sleeve anchor's clip, which reduces the risk of cracking the brick face in softer or older walls.

What's the difference between a loose bolt and bolt type shield anchor?

A loose bolt (projecting) anchor leaves a threaded stud standing proud of the wall, so the fixture fits over it and is secured with a nut. Bolt-type versions have the head on the anchor itself and clamp the fixture directly under it.

Can a shield anchor be removed?

Yes. Unscrew the bolt and it comes out of the shield; the shield itself usually stays in the wall, which can be left in place or tapped deeper and filled.

What drill size do I need for a shield anchor?

Match the hole diameter to the anchor's specified drill size — usually the nominal diameter (e.g. M10 → 10mm masonry bit) — and drill to the stated depth so the shield seats fully below the surface.

Fastco stocks shield anchors (loose bolts) for brick and concrete in the core trade sizes, alongside sleeve anchors, drop-in anchors and heavy-duty concrete anchors. With over 25 years supplying trades across the UK, if you're not sure which fixing suits your substrate, the team is on 01270 252326 Monday to Friday.