Lock Nuts

A lock nut is a nut designed to resist loosening under vibration, torque cycles and thermal movement — the forces that slowly back ordinary nuts off a bolt. Any threaded joint can shake loose over time; a lock nut adds friction or a positive mechanical barrier so it doesn't. In this guide we cover how the main types work, where each one earns its place, and the fitting habits that stop fasteners working loose for good.

What is a lock nut?

A lock nut is any nut with a built-in feature that resists self-loosening. Where a standard hex nut relies entirely on thread contact — and only needs a bit of vibration to start creeping round the bolt — a lock nut fights back in one of two ways:

  • Friction (prevailing torque) nuts grip the thread constantly, whether or not the nut is tightened. Nylon-insert and all-metal lock nuts both work this way.
  • Mechanical barrier nuts physically block rotation — castellated nuts held with a split pin are the classic example.

The most common by far on site is the nyloc — a hex nut with a nylon collar at the top of the thread.

How do lock nuts work?

The most common type, the nyloc, has a nylon ring set into the top face. As the nut is threaded on, the bolt forms its own thread through the nylon, which squeezes the bolt tightly along the whole engagement. That constant pinch is what resists vibration — and it's why a nyloc feels stiff to run down even before you apply a spanner.

All-metal lock nuts achieve the same grip without nylon: part of the nut's thread is deliberately distorted (crimped or ovalised), so the bolt has to force through a slightly out-of-shape section. The metal bites the bolt and holds it under load and vibration alike.

Which type of lock nut should you use?

 Nyloc (nylon insert)All-metal (stover type)Flange (serrated)
How it gripsNylon collar pinches the boltDistorted thread bites the boltSerrated face digs into the mating surface
Temperature limitAround 120°C — nylon softens above thisNo soft limit — works at full metal temperaturesNo soft limit
ReusabilityFew times at most — grip fades each useGood — can be reused several timesReusability depends on the serrations and surface
Best forGeneral trade work: brackets, frames, machinery at normal temperaturesEngine bays, exhausts, plant and high-temp environmentsSoft or painted surfaces, and where washers are skipped
Watch out forNot for hot zones or aggressive chemicalsSlightly more torque to run downSerrations mark the surface underneath

Two more specialist types worth knowing: jam nuts (a thin nut locked hard against a second full nut, used where space is tight) and castellated nuts (slotted tops pinned with a split pin — positive locking for steering, axles and safety-critical pivots).

When should you use a lock nut?

Any joint that sees vibration, movement or frequent load changes is a candidate. Typical trade jobs: machinery guards and mounts, gate hinges and auto gates, trailer and vehicle fixings, plant and generator mounts, pipework supports and anywhere a standard nut has visibly worked loose before.

For static joints — a bracket bolted to a solid wall, torqued once and never disturbed — a standard hex nut with a good washer is usually all you need. Lock nuts cost more; save them for where loosening is a genuine risk.

Installation tips that stop nuts working loose

  • Run the nyloc past the nylon before torquing. The clamping force should come from the metal thread contact, not from crushing the nylon against the joint face. If the nylon is doing the clamping, you'll deform it and lose the lock.
  • Torque properly. A lock nut adds running torque before the joint is loaded — follow the fastener's torque spec from the point the nut is fully engaged.
  • Replace nylocs that have been removed a few times. Each removal wears the nylon and reduces the locking grip. If it spins on freely, it's not locking anymore.
  • Match the grade. An 8.8 bolt with a 4.8 nut is a weak link — keep bolt and nut grades matched.
  • Full thread engagement. Aim for at least one full thread (ideally more) showing past the nut — short engagement is a common cause of joints creeping.

FAQ

What does a lock nut do?

It resists a nut working loose under vibration and load changes. Nylon-insert and all-metal types add constant friction to the thread; castellated and pinned types add a positive mechanical barrier.

How does a nyloc nut work?

A nylon collar at the top of the nut is compressed by the bolt as it's threaded through. The collar grips the bolt over the full engagement, adding constant resistance that stops the nut creeping round under vibration.

Can you reuse a nyloc nut?

Once or twice at most. Every pass through the nylon wears it and reduces the locking force — if the nut runs on with no resistance, it has lost its lock and should be replaced.

Which lock nut is best for high temperatures?

All-metal lock nuts. Nylon softens at around 120°C, so nylocs are unsuitable for engine bays, exhausts and hot plant — use a distorted-thread all-metal nut instead.

Do you still need a washer with a lock nut?

With a flange lock nut, no — the built-in flange spreads the load. With a nyloc or all-metal nut, a washer under the nut is still good practice on soft or oversized holes to spread the load and protect the surface.

Fastco stocks nuts for trade and DIY use — including nyloc and locking types across the core sizes — alongside a full range of fasteners and fixings. With over 25 years supplying trades across the UK, if you're not sure which nut suits the job, the team is on 01270 252326 Monday to Friday.